New Holland Workmaster 25S Attachments & Implements

The New Holland Workmaster 25S is a 24.7 HP compact tractor producing 17.4 PTO HP through a 540 RPM PTO, with a Limited Category I hitch and a 3-point lift capacity of 870 lb. Below: every attachment in our database checked against these specs.

Engine horsepower: 24.7 HP
PTO horsepower: 17.4 HP
PTO speeds: 540 RPM
Hitch: Limited Category I (Limited Category 1)
3-point lift capacity: 870 lb
Class: Sub-compact
Series: Workmaster Series
Front loader: 235TL

Attachment fit for the Workmaster 25S is decided by four of these figures: hitch category, PTO horsepower, PTO shaft speed, and implement weight against the 870 lb three-point lift rating. Because this is a sub-compact tractor, implements must also be rated for sub-compact use. Front-mount attachments additionally require the correct loader quick-attach type and, for grapples, a third hydraulic function. Every figure above is read from manufacturer documentation, linked on the page.

How the Workmaster 25S compares

The New Holland Workmaster 25S is rated at 17.4 PTO horsepower, which is more than 15 of the other 194 tractors in our database (the median is 31). Among the 13 New Holland models in the database it ranks 13th by PTO horsepower. Its PTO figure is 70 percent of its 24.7 engine horsepower; across the database the median is 82 percent.

Its three-point lift is 870 lb at 24 inches behind the lift points, more than 21 of the 173 other tractors that publish one (the median is 2,081 lb). No loader data is on file for it, so front-loader attachments are listed without a lift verdict.

Of the 173 attachments checked, 0 are full matches, 115 are compatible with notes and 58 are ruled out. The median tractor in the database has 133 full matches, and this one has more than 0 of the other 194. The 58 ruled out fail on PTO horsepower (58), hitch category (1) and lift capacity (5); a pairing can fail on more than one check.

It has no full match among the 18 rotary cutters, 19 rotary tillers, 22 box blades, 15 post hole diggers, 16 finish mowers, 12 snow blowers, 15 rear blades, 11 flail mowers, 14 landscape rakes, 13 grapples, 7 pallet forks, 6 bale spears and 5 land planes.

The closest tractors by PTO horsepower are the John Deere 3025E (17.4 HP, the same), the Kubota B2301HSD (17.4 HP, the same), the LS Tractor MT125 (17.2 HP, −0.2).

Compare: John Deere 3025E · Kubota B2301HSD · LS Tractor MT125

New Holland Workmaster 25S attachments by task

Checked against every attachment in the database, the New Holland Workmaster 25S returns 0 full matches, 115 compatible with notes, and 58 ruled out.

What fits the New Holland Workmaster 25S (0)

No full matches in our current database for this tractor.

Compatible with notes (115)

Showing 8 of 115, the ones closest to this tractor's limits.

Land Pride SB1051 — Snow blower · 18+ HP · 390 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Land Pride SB1064 — Snow blower · 18+ HP · 501 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Frontier RC2048 — Rotary cutter · 18+ HP · 516 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
King Kutter PHD-YK — Post hole digger · 18+ HP · 331 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Titan Attachments PHD 9" — Post hole digger · 18+ HP · 223 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Titan Attachments Finish Mower 48" — Finish mower · 18+ HP · 430 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Farmry TSB60 — Snow blower · 18+ HP · 715 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Woods TS44 — Rotary tiller · 18+ HP · 410 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.

Does not fit the Workmaster 25S (58)

Showing 8 of 58, the ones closest to this tractor's limits.

King Kutter RTG-60 — Rotary tiller · 20+ HP · 380 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Woods RD72 — Finish mower · 20+ HP · 603 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Land Pride RCR1260 — Rotary cutter · 20+ HP · 496 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Land Pride RTA1258 — Rotary tiller · 20+ HP · 448 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Land Pride RTR1258 — Rotary tiller · 20+ HP · 463 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
CountyLine FM5CL — Finish mower · 20+ HP · 628 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
Frontier RC2060 — Rotary cutter · 20+ HP · 590 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
King Kutter L-60-40-P — Rotary cutter · 20+ HP · 540 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.

Frequently asked questions

What is the PTO horsepower of the New Holland Workmaster 25S?

The New Holland Workmaster 25S produces 17.4 PTO horsepower (engine HP: 24.7), per New Holland Workmaster 25S. NewHolland.com.

What 3-point hitch category does the New Holland Workmaster 25S use?

The New Holland Workmaster 25S uses Limited Category I.

What is the lift capacity of the New Holland Workmaster 25S?

The New Holland Workmaster 25S has a 3-point lift capacity of 870 lbs at 24 inches behind the lift points.

What rotary cutters fit the New Holland Workmaster 25S?

No rotary cutters in our current database are a full match for the Workmaster 25S. Check the "Compatible with notes" and incompatible sections below for the closest options.

Will a King Kutter RTG-60 fit the New Holland Workmaster 25S?

No. The King Kutter RTG-60 is incompatible with the Workmaster 25S. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.4) is more than 10% below the implement minimum (20).