John Deere 1025R Attachments & Implements

The John Deere 1025R is a 23.9 HP compact tractor producing 17.2 PTO HP through a 540 RPM PTO, with a Limited Category 1. IMatch compatible hitch and a 3-point lift capacity of 758 lb. Below: every attachment in our database checked against these specs.

Engine horsepower

23.9 HP

PTO horsepower

17.2 HP

PTO speeds

540 RPM

Hitch

Limited Category 1. IMatch compatible (Limited Category 1)

3-point lift capacity

758 lb

Class

Sub-compact

Series

1 Series

Front loader

120R

Loader lift at pivot pin

803 lb

Loader quick-attach

JDQA

Attachment fit for the 1025R is decided by four of these figures: hitch category, PTO horsepower, PTO shaft speed, and implement weight against the 758 lb three-point lift rating. Because this is a sub-compact tractor, implements must also be rated for sub-compact use. Front-mount attachments additionally require the correct loader quick-attach type and, for grapples, a third hydraulic function. Every figure above is read from manufacturer documentation, linked on the page.

How the 1025R compares

The John Deere 1025R is rated at 17.2 PTO horsepower, which is more than 12 of the other 194 tractors in our database (the median is 31). Among the 19 John Deere models in the database it ranks 17th by PTO horsepower. Its PTO figure is 72 percent of its 23.9 engine horsepower; across the database the median is 82 percent.

Its three-point lift is 758 lb at 24 inches behind the lift points, more than 19 of the 173 other tractors that publish one (the median is 2,081 lb). Its loader lifts about 525 lb at 24 inches forward of the pin (500 mm forward of pin (metric SAE). Close approximation), more than 7 of the 65 other tractors with loader data on file (the median is 812 lb).

Of the 173 attachments checked, 0 are full matches, 110 are compatible with notes and 63 are ruled out. The median tractor in the database has 133 full matches, and this one has more than 0 of the other 194. The 63 ruled out fail on PTO horsepower (58), hitch category (1) and lift capacity (12); a pairing can fail on more than one check.

It has no full match among the 18 rotary cutters, 19 rotary tillers, 22 box blades, 15 post hole diggers, 16 finish mowers, 12 snow blowers, 15 rear blades, 11 flail mowers, 14 landscape rakes, 13 grapples, 7 pallet forks, 6 bale spears and 5 land planes.

The closest tractors by PTO horsepower are the John Deere 2025R (17.2 HP, the same), the LS Tractor MT125 (17.2 HP, the same), the John Deere 3025E (17.4 HP, +0.2).

Compare: John Deere 2025R · LS Tractor MT125 · John Deere 3025E

John Deere 1025R attachments by task

Checked against every attachment in the database, the John Deere 1025R returns 0 full matches, 110 compatible with notes, and 63 ruled out.

What fits the John Deere 1025R (0)

No full matches in our current database for this tractor.

Compatible with notes (110)

Showing 8 of 110, the ones closest to this tractor's limits.

• Titan Attachments Economy Grapple 72" — Grapple · 510 lbs. Loader required, confirm your loader model supports this attachment (SSQA / pin-on / Euro quick-attach). This attachment weighs 510 lbs against 525 lbs of usable capacity (500 mm forward of pin (metric SAE). Close approximation), consuming 97% of the loader before you pick anything up. That leaves roughly 15 lbs for material. It will mount and lift, but expect to be capacity-limited on real loads.
• Land Pride SB1051 — Snow blower · 18+ HP · 390 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Land Pride SB1064 — Snow blower · 18+ HP · 501 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Frontier RC2048 — Rotary cutter · 18+ HP · 516 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• King Kutter PHD-YK — Post hole digger · 18+ HP · 331 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Titan Attachments PHD 9" — Post hole digger · 18+ HP · 223 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Titan Attachments Finish Mower 48" — Finish mower · 18+ HP · 430 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Farmry TSB60 — Snow blower · 18+ HP · 715 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. PTO horsepower is marginal, verify with implement manufacturer before operating at full load. Lift capacity headroom is tight, recommend adding front ballast weights. This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.

Does not fit the 1025R (63)

Showing 8 of 63, the ones closest to this tractor's limits.

• King Kutter RTG-60 — Rotary tiller · 20+ HP · 380 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Woods RD72 — Finish mower · 20+ HP · 603 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Land Pride RCR1260 — Rotary cutter · 20+ HP · 496 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Land Pride RTA1258 — Rotary tiller · 20+ HP · 448 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Land Pride RTR1258 — Rotary tiller · 20+ HP · 463 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• CountyLine FM5CL — Finish mower · 20+ HP · 628 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• Frontier RC2060 — Rotary cutter · 20+ HP · 590 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.
• King Kutter L-60-40-P — Rotary cutter · 20+ HP · 540 lbs. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20). This implement is not specifically rated for sub-compact tractors, verify clearance and geometry with your dealer.

Frequently asked questions

What is the PTO horsepower of the John Deere 1025R?

The John Deere 1025R produces 17.2 PTO horsepower (engine HP: 23.9), per John Deere 1025R. Deere.com.

What 3-point hitch category does the John Deere 1025R use?

The John Deere 1025R uses Limited Category 1. IMatch compatible.

What is the lift capacity of the John Deere 1025R?

The John Deere 1025R has a 3-point lift capacity of 758 lbs at 24 inches behind the lift points.

What rotary cutters fit the John Deere 1025R?

No rotary cutters in our current database are a full match for the 1025R. Check the "Compatible with notes" and incompatible sections below for the closest options.

Will a King Kutter RTG-60 fit the John Deere 1025R?

No. The King Kutter RTG-60 is incompatible with the 1025R. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised. Tractor PTO HP (17.2) is more than 10% below the implement minimum (20).