King Kutter RB-72

The King Kutter RB-72 is a rear blade with no PTO requirement, attaching via Category I 3-point hitch and weighing 265 lbs. Verified against every tractor in our database below.

Type

Rear blade

Hitch category

Category I

Minimum PTO horsepower

None required

PTO speed

No PTO drive

Working weight

265 lb

Working width

72 in

Sub-compact rated

Yes

A tractor fits this rear blade when its hitch accepts Category I implements, and its three-point lift capacity exceeds the 265 lb working weight with headroom for the load the implement carries. The manufacturer rates this model for sub-compact tractors. Weight and horsepower figures here are read from the manufacturer document linked on the page, not from a retail listing.

Which tractors fit the King Kutter RB-72

Checked against every tractor in the database, the King Kutter RB-72 is a full match on 173 models, fits 22 with notes, and does not fit 0.

Tractors that fit (173)

Showing 8 of 173.

• Kubota BX1880 — 13.7 PTO HP · 680 lbs lift
• Kubota BX2380 — 17.7 PTO HP · 680 lbs lift
• Kubota BX2680 — 19.5 PTO HP · 680 lbs lift
• Kubota BX23S — 17.7 PTO HP · 680 lbs lift
• Kubota B2601HSD — 19.5 PTO HP · 1290 lbs lift
• Kubota B2301HSD — 17.4 PTO HP · 1411 lbs lift
• Kubota L2501 — 20.5 PTO HP · 1918 lbs lift
• Kubota L3301 — 27.7 PTO HP · 1985 lbs lift

Compatible with notes (22)

Showing 8 of 22.

• John Deere 1023E — 14.9 PTO HP · 758 lbs lift. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised.
• John Deere 1025R — 17.2 PTO HP · 758 lbs lift. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised.
• John Deere 2025R — 17.2 PTO HP · 915 lbs lift. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised.
• Mahindra eMax 20S — 14.2 PTO HP · 680 lbs lift. The Mahindra eMax 20S has a Category 1 Narrow hitch. Pin diameters are standard Category 1, so this implement will pin up, but the lower links sit closer together than the 26-inch Category 1 spacing. Measure your lower-link spread against this implement's pin spacing before buying - many Category 1 implements fit once the links are adjusted, and some do not.
• New Holland Workmaster 25S — 17.4 PTO HP · 870 lbs lift. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised.
• New Holland Boomer 24 — 18.5 PTO HP · 1433 lbs lift. This tractor uses a Limited Category I hitch. Pin diameters and lower-link spacing meet the standard Category I specification, so Category I implements mount normally - what is limited is lift height, ground clearance and lift-frame capacity. Check the implement's weight against this tractor's 3-point lift figure, and expect less clearance under the implement when raised.
• TYM T224 — 15.1 PTO HP · 679 lbs lift. The TYM T224 has a Category 1 Narrow hitch. Pin diameters are standard Category 1, so this implement will pin up, but the lower links sit closer together than the 26-inch Category 1 spacing. Measure your lower-link spread against this implement's pin spacing before buying - many Category 1 implements fit once the links are adjusted, and some do not.
• TYM T264 — 18.2 PTO HP · 1102 lbs lift. The TYM T264 has a Category 1 Narrow hitch. Pin diameters are standard Category 1, so this implement will pin up, but the lower links sit closer together than the 26-inch Category 1 spacing. Measure your lower-link spread against this implement's pin spacing before buying - many Category 1 implements fit once the links are adjusted, and some do not.

Tractors that do not fit (0)

None. Every tractor in our database is compatible.

Frequently asked questions

What is the minimum PTO horsepower for the King Kutter RB-72?

The King Kutter RB-72 requires 0 PTO HP minimum.

What hitch category does the King Kutter RB-72 use?

The King Kutter RB-72 attaches via Category I 3-point hitch.

How heavy is the King Kutter RB-72?

265 lbs.

Does the King Kutter RB-72 fit a Kubota BX2380?

Verdict: FULL MATCH.

Is the King Kutter RB-72 sub-compact compatible?

Yes. The manufacturer rates this attachment for sub-compact tractor geometry.